多产品生产计划与非周期预防维修整合优化模型

doi:10.16381/j.cnki.issn1003-207x.2017.11.020

中国管理科学 ›› 2017, Vol. 25 ›› Issue (11): 189-196.doi: 10.16381/j.cnki.issn1003-207x.2017.11.020

• 论文 • 上一篇

多产品生产计划与非周期预防维修整合优化模型

刘学娟¹, 赵斐², 马晓洋¹

1. 北京科技大学东凌经济管理学院, 北京 100083;
2. 东北大学秦皇岛分校管理学院, 河北秦皇岛 066004

收稿日期:2016-05-09 修回日期:2017-04-16 出版日期:2017-11-20 发布日期:2018-01-31
通讯作者: 刘学娟(1982-),女(汉族),河北沧州人,北京科技大学东凌经济管理学院,讲师,博士后,研究方向:生产运作管理、系统可靠性管理,E-mail:liuxj@ustb.edu.cn E-mail:liuxj@ustb.edu.cn
基金资助:
国家自然科学基金资助项目（71601019，71231001）；中央高校基本科研业务费专项资金资助项目（FRF-TP-16-007A1）；中国博士后科学基金项目（2017M610049）；教育部人文社会科学研究项目（No.16YJC630174）

Joint Optimal Multi-product Production and Non-cyclical Preventive Maintenance Planning Model

LIU Xue-juan¹, ZHAO Fei², MA Xiao-yang¹

1. Donlinks School of Economics and Management, University of Science and Technology Beijing, Beijing 100083, China;
2. School of Management, Northeastern University at Qinhuangdao, Qinhuangdao 066004, China

Received:2016-05-09 Revised:2017-04-16 Online:2017-11-20 Published:2018-01-31

摘要/Abstract

摘要： 本文将离散制造业生产计划问题与生产设备的非周期预防性维修相结合进行研究，在有限的生产计划期中包含若干个等长度的时段，各个时段中都有需要被满足的多种类的产品需求量，并将每个时段的末期作为可选的预防性维修窗口，利用实际的设备运行时间计算设备维修对生产能力的占用。计划期内生产和维修的费用包括：生产费用、库存费用、延期交货费用、设备调整费用和设备维修费用，以最小化这些费用的总和为目标建立整合模型并进行优化，确定最优的生产计划及设备预防性维修序列。并运用数值案例对所建立的模型进行应用分析。

关键词: 生产计划, 库存, 预防性维修, 延迟时间

Abstract: The production and maintenance activities share the same system in reality, so the conflict is inevitably generated. If the arrangement of the production plan and the maintenance schedule are not reasonable, the shortage of the products and the improper maintenance (inadequate maintenance or excessive maintenance) may occur. To avoid this negative influence, the integrated model of the production planning problem of discrete manufacturing industry and non-cyclical preventive maintenance is proposed in this paper. The finite production planning horizon is composed of several equal-length periods. in each period, the demands of multi product should be satisfied by the production quantity in this period and the inventory of last period, otherwise, the backorder will happen. The non-cyclical preventive maintenance can be carried out at the end of some production periods, and the minor repair is used to deal with system failures. The occupation of production capacity is composed of maintenance and system setup. In each period, the time can be used to product is equal to the length of the period minus the maintenance and setup time, and the actual running time of system is used to formulate the failure numbers. Furthermore, the maintenance time of failure can be presented. Then' the integrated production and maintenance model is developed in the form of mathematical programming. The objective of the model is to determining the optimal production panning and preventive maintenance sequence that minimizes the sum of the production cost, inventory cost, setup cost and maintenance cost. Based on the production data of steel grating gathered from a steel facility, a case study is presented to illustrate the integrated model, the optimal production plan and the optimal maintenance schedule are determined simultaneously. Moreover the result shows that the optimal maintenance schedule is not cyclical, since the non-cyclical maintenance policy presents more maintenance sequences than that presented by cyclical maintenance policy.

Key words: production planning, inventory, preventive maintenance, delay-time

中图分类号:

F272

刘学娟, 赵斐, 马晓洋. 多产品生产计划与非周期预防维修整合优化模型[J]. 中国管理科学, 2017, 25(11): 189-196.

LIU Xue-juan, ZHAO Fei, MA Xiao-yang. Joint Optimal Multi-product Production and Non-cyclical Preventive Maintenance Planning Model[J]. Chinese Journal of Management Science, 2017, 25(11): 189-196.

参考文献

[1] 孔继利,苑春荟,杨福兴,等. 带搬运时间的批量生产制造系统生产作业计划方法[J]. 系统工程理论与实践,2015, 35(11):2821-2831.

[2] 周瑜,寇纲,尔古打机. 考虑维修效果与计划水平的预防维修决策优化[J]. 系统工程学报,2015, 30(2):281-288.

[3] Liu Xuejuan, Wang Wenbin, Peng Rui. An integrated production, inventory and preventive maintenance model for a multi-product production system[J]. Reliability Engineering and System Safety, 2015, 137:76-86.

[4] Liu Xuejuan, Wang Wenbin, Zhao Fei, et al. Joint lot-size and preventive maintenance optimization for a production system[J]. International Journal of Performability Engineering, 2015, 11(1):91-96.

[5] 刘学娟, 赵斐. 多产品生产计划与设备维修整合优化模型[J]. 工业工程与管理, 2015, 20(4):23-28.

[6] 祝颖,冷乔,王丽亚,等. 带缓冲多阶段系统的生产批量与维护计划集成优化[J]. 工业工程与管理,2015, 20(6):48-53.

[7] 廖雯竹. 基于设备衰退机制的预知性维护策略及生产排程集成研究[D]. 上海:上海交通大学, 2011.

[8] 王建军,刘晓盼,刘锋,等. 随机机器故障下加工时间可控的并行机鲁棒调度[J]. 中国管理科学,2017, 25(3):137-146.

[9] Weinstein L, Chung CH. Integrating maintenance and production decisions in a hierarchical production planning environment[J]. Computers and Operations Research, 1999,26(10-11):1059-1074.

[10] Aghezzaf E H, Jamali M A, Ait-Kadi D. An integrated production and preventive maintenance planning model[J]. European Journal of Operational Research, 2007, 181(2):679-685.

[11] Fitouhi M C, Nourelfath M. Integrating noncyclical preventive maintenance scheduling and production planning for a single machine[J]. International Journal of Production Economics, 2012, 136(2):344-351.

[12] Fitouhi M C, Nourelfath M. Integrating noncyclical preventive maintenance scheduling and production planning for multi-state systems[J]. Reliability Engineering and System Safety, 2014, 121:175-186.

[13] Nourelfath M, Fitouhi M C, Machani M. An integrated model for production and preventive maintenance planning in multi-state systems[J]. IEEE Transactions on Reliability, 2010, 59(3):496-506.

[14] Christer A H, Waller W M. Reducing production downtime using delay time analysis[J]. Journal of Operational Research Society, 1984, 35(6):499-512.

[15] 王文彬, 赵斐, 彭锐. 基于三阶段故障过程的多重点检策略优化模型[J]. 系统工程理论与实践, 2014, 34(1):223-232.

[16] Wang Wenbin. An overview of the recent advances in delay-time-based maintenance modeling[J]. Reliability Engineering and System Safety, 2012, 106:165-178.

[17] Wang Wenbin. Models of inspection, routine service, and replacement for a serviceable one-component system[J]. Reliability Engineering and System Safety, 2013, 116(8):57-63.

[18] Flage R. A delay time model with imperfect and failure-inducing inspections[J]. Reliability Engineering and System Safety, 2014,124:1-12.

[19] Wang Wenbin, Banjevic D, Pecht M. A multi-component and multi-failure mode inspection model based on the delay time concept[J]. Reliability Engineering and System Safety, 2010, 95(8):912-920.

[20] Cunningham A, Wang Wenbin, Zio E, et al. Application of delay-time analysis via Monte Carlo simulation[J]. Journal of Marine Engineering and Technology, 2011, 10(3):57-72.

[21] 郑睿, 吕文元. 自动生产线的同步维修模型及实例研究[J]. 中国管理科学, 2011, 19(1):119-125.

[22] 郑睿,吕文元. 考虑故障停机的生产控制与维修计划联合决策模型[J]. 中国管理科学,2016, 24(8):116-122.

[23] Liao G L. Optimal economic production quantity policy for randomly failing processes with minimal repair, backorder and preventive maintenance[J]. International Journal of Systems Science, 2012, 44(9):1602-1612.

[24] Karimi B, Fatemi-Ghomi SMT, Wilson JM. The capacitated lot sizing problem:A review of models and algorithms[J]. Omega, 2003, 31(5):365-378.

[25] Baker R D, Wang Wenbin. Developing and testing the delay-time model[J]. Journal of the Operational Research Society, 1993, 44(4):361-374.

多产品生产计划与非周期预防维修整合优化模型

Joint Optimal Multi-product Production and Non-cyclical Preventive Maintenance Planning Model

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

Metrics

本文评价

推荐阅读 10

[1]	邱若臻, 李旭阁. 考虑策略型消费者的在线零售商库存信息披露及联合定价、库存决策模型[J]. 中国管理科学, 2021, 29(1): 59-71.
[2]	熊浩, 鄢慧丽. 考虑多种安全库存策略的选址-库存问题研究[J]. 中国管理科学, 2021, 29(1): 72-81.
[3]	纪雅杰, 马德青, 胡劲松. 供应商管理库存下基于消费者行为偏好的全渠道运营策略[J]. 中国管理科学, 2021, 29(1): 82-96.
[4]	卢震, 徐健, 杨允锋. 考虑质量相关性需求与完全预防性维修的EPQ决策[J]. 中国管理科学, 2020, 28(5): 71-78.
[5]	吴江, 王旻轲, 谭涛, 张培文. 非平稳需求下考虑碳配额的供应链选址-库存模型与算法研究[J]. 中国管理科学, 2020, 28(3): 162-173.
[6]	邱若臻, 张多琦, 孙艺萌, 关志民. 供需不确定条件下基于CVaR的零售商库存鲁棒优化模型[J]. 中国管理科学, 2020, 28(12): 98-107.
[7]	江秋阳, 陶峰, 范体军, 黎建强. 基于RFID技术的双供应链投资决策研究[J]. 中国管理科学, 2020, 28(11): 120-129.
[8]	龚媛媛, 肖勇波. 新鲜产品跨季销售中的动态库存管理策略研究[J]. 中国管理科学, 2019, 27(7): 83-93.
[9]	曹裕, 易超群, 万光羽. 基于“搭便车”行为的双渠道供应链库存竞争和促销策略[J]. 中国管理科学, 2019, 27(7): 106-115.
[10]	士明军, 王勇, 但斌, 文悦. 绿色供应链中不对称需求预测下的信息共享研究[J]. 中国管理科学, 2019, 27(4): 104-114.
[11]	樊双蛟, 王旭坪. 考虑退货的定价和订货优化及信息发布美化策略[J]. 中国管理科学, 2019, 27(3): 116-127.
[12]	宋江海, 池宏, 高敏刚. 航空公司机上周转品多基地库存优化模型[J]. 中国管理科学, 2019, 27(2): 119-128.
[13]	王淑云, 姜樱梅, 牟进进. 基于新鲜度的冷链一体化库存与定价联合决策[J]. 中国管理科学, 2018, 26(7): 132-141.
[14]	王海燕, 隽志如, Henry Xu. 需求分布规律变化情况下的报童订货策略[J]. 中国管理科学, 2018, 26(4): 22-29.
[15]	张剑, 张菊亮. 供应不确定条件下多周期库存博弈[J]. 中国管理科学, 2018, 26(4): 67-77.